Vibration Basics - Definition

Before giving the details of the calculations required for suspensions able to provide vibration and shock protection, the vibration terminology used in this catalogue is defined.

Coupling

The natural frequencies of a system are interdependent. If the natural frequency for a given degree of freedom is excited, it may cause a response at the same frequency in the other degrees of freedom due to the coupling effect. When designing a suspension for a particular application, coupling must be taken into consideration. The stiffness and damping of the mountings in each axis should be considered as well as the moments of inertia for the rotational behaviour.

Creep

Irreversible change with time of the deformation under constant load.

Critical damping

Damping value for which the return to equilibrium is asymptotic and without oscillation.

Damping

Damping is the force that reduces the amplitude of a vibration. There are two main types of damping :

  • Frictional damping (static friction): the force is independant of the relative speed of the suspended mass relative to the supporting base. For a given displacement the force is constant. For movement, a force has to be applied that is at least as great as the damping force.
  • Viscous damping (characteristic of shock absorbers) : the force is dependent on the speed of the suspended assembly relative to the supporting base. Viscous damping is dynamic and does not change the static equilibrium position.

Decibels

Dimensionless measure of the ratio of two parameters of a vibration system. dB = 10 log10 X1/X2 where X1 and X2 may be, for example, the amplitudes of vibration above and below the mounting system.

Deflection

Displacement associated with the application of a static or dynamic force or a combination of forces.

Degrees of freedom

The number of degrees of freedom is the number of independent parameters that determine the position of the system at a given moment. - Linear movement along an axis. - Rotation round an axis. Freely suspended assemblies have 6 degrees of freedom -3 mutually perpendicular and 3 rotational.

Elastic mountings

Elastic mountings have a wide range of both elastic and damping properties.

Elasticity

Elasticity describes the reversible deformation of an elastic mounting where the deformation is approximately proportional to the load.

Elastomer

Elastomer is a general term for any natural or synthetic rubber. The choice of elastomer to be used for a mounting system depends on the environment and application.

Forced vibration

Vibration imposed on the system either by its own operation or by its surroundings.

Matching

For guidance and radar systems, it may be necessary to use a set of mountings with matched dynamic characteristics (stiffness and damping) to avoid coupling and improve stability.

Natural frequency

When a system is displaced from its position of equilibrium and released, it oscillates at its natural frequency. The natural frequency of a system is usually expressed in Hertz. In theory, there are as many natural frequencies as degrees of freedom.

Natural vibration

Vibration at the natural frequency in the absence of external influences.

Noise (not to be confused with sound)

Noise is a random vibration. It can be broken down into a set of unrelated, elementary components. Vibration can cause the emission of audible noise.

Noise is usually either airborne or propagated through the structure. An elastic mounting system only reduces structure borne noise.

Q factor

A quantity which is a measure of the sharpness of resonance or frequency selectivity of a resonant oscillatory system having a single degree of freedom. Note: Q = 1 / (2C/Cc) when C/Cc is a not too high damping ratio.

Random vibration

Random vibration is the most commonly occurring form of vibration. It is characterised by the fact that neither the amplitude nor frequency of the vibration are constant, as opposed to sinusoidal vibration.

Resilience

Ability of a system to return to its initial position after being subjected to one or several forces.

Resonance

Resonance of a system in forced oscillation exists when any change however small, in the frequency of excitation causes a decrease in a response of the system.

Spectral power density

Expression used to describe random vibration. It is expressed in g2 /Hz. The power spectral density of a quantity is the mean-square value of that part of the quantity passed by a narrow-band filter of contrefrequency f, per unit bandwidth, in the limit as the bandwidth approaches zero and the averaging time approaches infinity.

Stiffness

Characteristics of a mounting system. The force applied divided by the deflection. An equifrequent mounting system has the same stiffness in all directions.

  • Linear stiffness :
    Kx along the X axis : longitudinal movement
    Ky along the Y axis : transverse movement
    Kz along the Z axis : vertical movement

    For each axis, the linear stiffness of the suspension is the sum of the linear stiffnesses of all the mountings.
    Kx = S Kx Ky = S Ky Kz = S Kz
    Linear stiffness is expressed in N/m or lb/in.
  • Torsional stiffness :
    Cx along the X axis = roll
    Cy along the Y axis = pitch
    Cz along the Z axis = yaw

    The torsional stiffness of the mounting system is dependent on :
    - the intrinsic stiffness of the mountings
    - the position and orientation of the mountings with respect to the center of gravity G of the system. Torsional stiffness is expressed in Nm /radian or in lb.in /°..

These six parameters, which, for a given mounting system, are interdependent (the interaction depends on the type, position and orientation of the mountings) are proportional to the stiffness of the mountings.

Transmissibility

The non dimensional ratio of the response amplitude of a system in steady-state forced vibration to the excitation amplitude. The ratio may be one of forces, displacements, velocities or accelerations.

Young's modulus

It is the ratio between the stress (the force per unit area applied) and the deformation rate (the fractional displacement).

The Young's modulus of elastomers, unlike those of metals, is non-linear and strongly dependent on load and temperature.